D690-04-00 3 I56-2783-004R
TONE SELECTION
Chime tone setting selection is accomplished by using the rotary switch on the
back of the product (see Table 4). The current draw for various tone settings
for chimes is listed in Table 5. The sound measurements for various chime
tone settings are shown in Table 6 for chime and chime/strobe products.
TABLE 4. CHIME PATTERNS
SETTING REPETITION RATE dB OUT
1 1 Second Chime High
2 1 Second Chime Low
3 1/4 Second Chime High
4 1/4 Second Chime Low
5 Temporal Chime High
6 Temporal Chime Low
7 5 Second Whoop High
8 5 Second Whoop Low
9 One Test Chime High
TABLE 5. CHIME CURRENT DRAW (mA)
SOUND PATTERN dB
8–17.5 VOLTS 16–33 VOLTS
DC FWR DC FWR
1 Second Chime High
34 50 58 51
1 Second Chime Low
30 51 51 54
1/4 Second Chime High
34 51 50 50
1/4 Second Chime Low
31 51 50 52
Temporal Chime High
30 50 48 54
Temporal Chime Low
30 47 50 51
5 Second Whoop High
32 52 34 54
5 Second Whoop Low
30 40 34 52
One Test Chime High
48 49 50 50
TERMINAL DEFINITIONS
MOUNTING
FIGURE 4.
1. Attach mounting plate to junction box. The mounting plate is compatible
with 4˝ square, single gang, double gang, and 4˝ octagon junction boxes.
If using a back box skirt, attach the mounting plate to the skirt and then
attach the entire assembly to the junction box.
2. Connect field wiring according to terminal definitions.
3. If the product is not to be installed at this point, use the dust cover to
prevent contamination of the wiring terminals of the mounting plate.
4. To attach product to mounting plate, hook tabs on the product housing
into the grooves on mounting plate. Then, swing product into position to
engage the pins on the product with the terminals on the mounting plate.
Make sure that the tabs on the back of the product housing fully engage
with the mounting plate.
5. Secure product by tightening the single mounting screw in the front of
the product housing.
A0353-00
A0350-00
SWITCH
POSITION SOUND PATTERN dB
8–17.5 VOLTS 16–33 VOLTS
DC FWR DC FWR
1 1 Second Chime High
58 59 61 61
2 1 Second Chime Low
51 51 52 52
3
1
/4 Second Chime High
63 64 66 66
4
1
/4 Second Chime Low
56 56 56 56
5 Temporal Chime High
62 64 68 69
6 Temporal Chime Low
54 56 57 57
7 5 Second Whoop High
68 71 75 77
8 5 Second Whoop Low
60 61 62 63
9 One Test Chime High
56 55 59 57
WIRING
FIGURE 1. NON-SYNCHRONIZED DEVICES; ANY COMBINATION OF
MODELS POWERED BY A 2-WIRE CIRCUIT
Chime
(+)
(–)
(+)
(–)
E
O
L
(+)
(–)
(+)
(–)
Chime/strobe
Chime
Two Wire System
Any Mix of Models
Wired for Tandem
Operation
Chime
Synchronization Module
(+)
(–)
(+)
(–)
E
O
L
(+)
(–)
(+)
(–)
Chime/strobe
Chime
Two Wire System
Any Mix of Models
Wired for Tandem
Operation
MDL
FIGURE 2. SYNCHRONIZED DEVICES; ANY COMBINATION OF
MODELS POWERED BY A 2-WIRE CIRCUIT
Chime
(+)
(–)
(+)
(–)
E
O
L
(+)
(–)
(+)
(–)
Chime/strobe
Chime
Two Wire System
Any Mix of Models
Wired for Tandem
Operation
Chime
Synchronization Module
(+)
(–)
(+)
(–)
E
O
L
(+)
(–)
(+)
(–)
Chime/strobe
Chime
Two Wire System
Any Mix of Models
Wired for Tandem
Operation
MDL
A0345-00
FIGURE 3.
TABLE 6. CHIME & CHIME/STROBE OUTPUT (dBA)
Wiring
NOTE: For further information on synchronization see MDL3, panel, or power
supply installation manual.
(4 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji