System-sensor B116LP Instrukcja Użytkownika Pobierz pdf

D150-01-00 1 I56-599-03R

B116LP Plug-in Detector Base

For use with the following smoke detectors:

In US: 1151, 2151

In Canada: 1151A, 2151A

In Europe: 1151E, 2151E

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue,

St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

Before Installing

Please thoroughly read the System Sensor manual I56-407,

Guide for Proper Use of System Smoke Detectors, which pro-

vides detailed information on detector spacing, placement,

zoning, wiring, and special applications. Copies of this

manual are available at no charge from System Sensor. (For

installation in Canada, please refer to CAN4-S524, Standard

for the Installation of Fire Alarm Systems and CEC Part 1,

Sec. 32.)

NOTICE: This manual should be left with the owner/user

of this equipment.

IMPORTANT: The detector used with this base must be

Specifications

Base Diameter: 6.2 inches (157 mm)

Base Height: 0.95 inches (24 mm)

Weight: 0.3 lb. (130 g)

Mounting: 4-inch square box with or without plaster ring. Min. Depth–1.5 inches

4-inch octagon box. Min. Depth–1.5 inches

3-1/2 inch-octagon box. Min. Depth–1.5 inches

50 mm box

60 mm box

70 mm box

Operating Temperature Range: 0° to +49°C (32° to 120°F) US and Canadian Installations

10°to 60°C (14° to 140°F) European Installations

Operating Humidity Range: 10% to 93% Relative Humidity

Electrical Ratings – includes base and detector

System Voltage: 24 VDC

Maximum Ripple Voltage: 4 Volts peak to peak

Start-up Capacitance: 0.02µF Maximum

Standby Ratings: 15 VDC Minimum

35 VDC Maximum

120 µA Maximum

Alarm Ratings: 8 V Minimum at 16 mA

12 V Maximum at 100 mA

(Alarm current MUST be limited to 100 mA maximum by the control panel.)

Relay Contact Ratings:

Resistive or Inductive (60% power factor) Load

Form C:* 2.0A @ 30 VAC/DC

0.6A @ 110 VDC

1.0A @ 125 VAC

Reset Voltage: 1.4 VDC Minimum

Reset Time: 0.3 Seconds Maximum

Start-up Time: 34.0 Seconds Maximum

*For Canadian installations relay contact ratings are 2.0A @ 30 VAC/DC.

tested and maintained regularly following NFPA 72 require-

ments. The detector used with this base should be cleaned

at least once a year.

General Description

The model B116LP plug-in detector base is used with

System Sensor model 1151, 1151A, and 1151E ionization

detector heads and model 2151, 2151A, and 2151E photo-

electronic detector heads. The capability of plugging these

detectors into a variety of special bases makes them more

versatile than equivalent direct-wired models. Refer to the

System Sensor catalog for other available plug-in detector

bases.

1 2 3 4

Podsumowanie treści

Strona 1 - B116LP Plug-in Detector Base

D150-01-00 1 I56-599-03RB116LP Plug-in Detector BaseFor use with the following smoke detectors:In US: 1151, 2151In Canada: 1151A, 2151AIn Europe: 1151

Strona 2 - D150-01-00 2 I56-599-03R

D150-01-00 2 I56-599-03RThe B116LP base is intended for use in 2-wire systems,with screw terminals provided for power and relay contactconnections. Th

Strona 3 - D150-01-00 3 I56-599-03R

CAUTIONOnce all the detector bases have been wired and mounted,and the loop wiring has been checked, the detector headsmay be installed in the bases.

Strona 4

Komentarze do niniejszej Instrukcji

Brak uwag

System-sensor B116LP Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Ekwipunek System-sensor B116LP. System Sensor B116LP User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek System-sensor B116LP